{"id":3106,"date":"2026-08-10T01:00:25","date_gmt":"2026-08-10T01:00:25","guid":{"rendered":"https:\/\/isaacprodetailing.com.au\/index.php\/2026\/08\/10\/first-wash-after-ceramic-coating\/"},"modified":"2026-08-10T01:00:26","modified_gmt":"2026-08-10T01:00:26","slug":"first-wash-after-ceramic-coating","status":"publish","type":"post","link":"https:\/\/isaacprodetailing.com.au\/index.php\/2026\/08\/10\/first-wash-after-ceramic-coating\/","title":{"rendered":"First wash after ceramic coating: safe steps for car owners"},"content":{"rendered":"<\/p>\n<p>Wait at least several days before your first full wash after ceramic coating, and always follow your installer\u2019s specific cure window. Detailers widely recommend a short initial curing timeframe, because the first week is the most critical for bonding. When you do wash, use a low-friction, pH-neutral hand wash with the two or three-bucket method. That\u2019s the whole rule in one sentence.<\/p>\n<ul>\n<li><strong>Avoid<\/strong> automatic or brush car washes during the entire cure period<\/li>\n<li><strong>Avoid<\/strong> any high-pressure chemical contact in the first 48 hours<\/li>\n<li><strong>Avoid<\/strong> touching painted surfaces unnecessarily in the first 48 hours<\/li>\n<li><strong>Acceptable<\/strong> in the first 48 hours: a light rinse with low-pressure water if unavoidable<\/li>\n<li><strong>Acceptable<\/strong>: blotting (not rubbing) bird droppings or sap with a damp microfibre<\/li>\n<\/ul>\n<p><strong>Pro Tip:<\/strong> <em>If you\u2019re unsure about your installer\u2019s cure window or you lack the right products, book a mobile detailer for the first wash. It protects your warranty and removes the guesswork entirely.<\/em><\/p>\n<hr>\n<h2 id=\"key-takeaways\">Key takeaways<\/h2>\n<p>Wait the full installer-recommended cure window, then use a pH-neutral hand wash with the two-bucket method for maintenance to keep your ceramic coating performing at its best.<\/p>\n<table>\n<thead>\n<tr>\n<th>Point<\/th>\n<th>Details<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Wait before washing<\/td>\n<td>Follow your installer\u2019s cure window; commonly 5\u20137 days, up to two weeks for some professional coatings.<\/td>\n<\/tr>\n<tr>\n<td>Use the right method<\/td>\n<td>Two or three-bucket method with grit guards and soft microfibre mitts protects the coating on every wash.<\/td>\n<\/tr>\n<tr>\n<td>Avoid automatic washes<\/td>\n<td>Brush car washes and harsh chemicals can void your warranty and degrade the coating permanently.<\/td>\n<\/tr>\n<tr>\n<td>Maintain a regular schedule<\/td>\n<td>Full hand wash every 2\u20133 weeks; professional decontamination every 3\u201312 months depending on exposure.<\/td>\n<\/tr>\n<tr>\n<td>Isaac\u2019s Pro Detailing<\/td>\n<td>Mobile first wash and maintenance service on the Sunshine Coast, using warranty-safe, pH-neutral products.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<hr>\n<h2 id=\"table-of-contents\">Table of Contents<\/h2>\n<ul>\n<li><a href=\"#what-to-do-in-the-hours-and-days-after-coating\">What to do in the hours and days after coating<\/a><\/li>\n<li><a href=\"#why-waiting-matters-how-ceramic-coatings-cure\">Why waiting matters: how ceramic coatings cure<\/a><\/li>\n<li><a href=\"#how-to-do-the-first-wash-safely-step-by-step\">How to do the first wash safely, step by step<\/a><\/li>\n<li><a href=\"#products-and-tools-that-are-safe-for-the-first-wash\">Products and tools that are safe for the first wash<\/a><\/li>\n<li><a href=\"#common-mistakes-that-damage-a-newly-cured-coating\">Common mistakes that damage a newly cured coating<\/a><\/li>\n<li><a href=\"#ongoing-care-after-the-first-wash-your-maintenance-schedule\">Ongoing care after the first wash: your maintenance schedule<\/a><\/li>\n<li><a href=\"#when-to-book-a-professional-first-wash-or-maintenance-service\">When to book a professional first wash or maintenance service<\/a><\/li>\n<li><a href=\"#a-sunshine-coast-detailers-practical-note\">A Sunshine Coast detailer\u2019s practical note<\/a><\/li>\n<li><a href=\"#isaacs-pro-detailing-mobile-first-wash-and-maintenance-on-the-sunshine-coast\">Isaac\u2019s Pro Detailing: mobile first wash and maintenance on the Sunshine Coast<\/a><\/li>\n<li><a href=\"#sources\">Sources<\/a><\/li>\n<\/ul>\n<h2 id=\"what-to-do-in-the-hours-and-days-after-coating\">What to do in the hours and days after coating<\/h2>\n<p>The coating is most vulnerable immediately after application. <a href=\"https:\/\/kmautodetailing.com.au\/resources\/ceramic-coating-aftercare\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Contamination that adheres in the first 48 hours can bond into a partially cured layer<\/a>, which is why the actions you take right away matter as much as the first wash itself.<\/p>\n<table>\n<thead>\n<tr>\n<th>Phase<\/th>\n<th>What\u2019s happening<\/th>\n<th>What you can do<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>first 48 hours<\/td>\n<td>Initial set; coating is soft and highly sensitive<\/td>\n<td>Keep car garaged or covered; no washing, no touching paint<\/td>\n<\/tr>\n<tr>\n<td>\u2014<\/td>\n<td>Surface hardening begins<\/td>\n<td>Still avoid washing; blot contaminants only<\/td>\n<\/tr>\n<tr>\n<td>Days 3\u20137<\/td>\n<td>Crosslinking progresses<\/td>\n<td>Keep dry where possible; no chemical contact<\/td>\n<\/tr>\n<tr>\n<td>Days 7\u201330<\/td>\n<td>Coating approaches full cure<\/td>\n<td>First full hand wash permitted after installer\u2019s window<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>A few practical habits for the first 48 hours:<\/p>\n<ul>\n<li>Park undercover or use a car cover to reduce exposure to dew, rain, and tree sap<\/li>\n<li>If a bird dropping lands on the car, blot it immediately with a damp microfibre; never rub<\/li>\n<li>Avoid touching the painted surfaces with bare hands, which can leave oils and fingerprints<\/li>\n<\/ul>\n<p><a href=\"https:\/\/ceramicpro.com\/wp-content\/uploads\/2022\/11\/Coating-Warranty-Aftercare.pdf\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Ceramic Pro\u2019s aftercare guidance<\/a> advises against washing for at least two weeks and stresses keeping the vehicle dry during the initial cure hours. Some professional-grade coatings carry that longer window, so always document your installer\u2019s specific instructions and keep them with your warranty paperwork.<\/p>\n<hr>\n<h2 id=\"why-waiting-matters-how-ceramic-coatings-cure\">Why waiting matters: how ceramic coatings cure<\/h2>\n<p>Ceramic coatings cure in two stages. The first is an initial surface set, where the coating firms up enough to resist light contact. The second is full crosslinking, where the silica or SiO2 molecules form a dense, interlocked network across the paint surface. That second stage is what delivers the hardness, hydrophobic performance, and chemical resistance you paid for.<\/p>\n<p><a href=\"https:\/\/kovalentcoatings.com\/ceramic-coating-cure-time\/\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Getting the coating wet before it fully cures can leave water marks or cause uneven performance<\/a>. Water itself isn\u2019t the only risk. Alkaline or acidic substances during the cure window can interfere with crosslinking, and physical abrasion, even light wiping, can disrupt the layer before it has locked in.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/csuxjmfbwmkxiegfpljm.supabase.co\/storage\/v1\/object\/public\/blog-images\/organization-15772\/1786073748248_Close-up-of-curing-ceramic-coating-with-water-beads.jpeg\" alt=\"Close-up of curing ceramic coating with water beads\"><\/p>\n<p>The result of premature exposure isn\u2019t always obvious immediately. You might notice hazing, water spots that won\u2019t shift, or patchy hydrophobic behaviour weeks later, all of which trace back to those first few days.<\/p>\n<p><strong>Pro Tip:<\/strong> <em>Australia\u2019s environment adds extra pressure during cure. Coastal salt air on the Sunshine Coast, hard bore water, eucalyptus sap, and intense UV all increase the risk of etching or water spotting on a partially cured surface. If you can\u2019t garage the car, a breathable car cover is worth using for the first week.<\/em><\/p>\n<hr>\n<h2 id=\"how-to-do-the-first-wash-safely-step-by-step\">How to do the first wash safely, step by step<\/h2>\n<p>Once your installer\u2019s wait period has passed, here\u2019s how to wash a ceramic coated car without damaging the finish. Work in the shade, in mild temperatures, and never on a hot panel.<\/p>\n<p><strong>What you\u2019ll need on hand:<\/strong><\/p>\n<ul>\n<li>Two or three clean buckets with grit guards<\/li>\n<li>pH-neutral car shampoo<\/li>\n<li>Foam gun or pump sprayer (optional but helpful)<\/li>\n<li>Two soft microfibre wash mitts (one for the body, one for lower panels)<\/li>\n<li>Separate wheel brush and bucket<\/li>\n<li>Multiple clean microfibre drying towels<\/li>\n<\/ul>\n<p><strong>The wash sequence:<\/strong><\/p>\n<ol>\n<li><strong>Choose your location.<\/strong> Work in shade, ideally early morning or late afternoon. Avoid washing in direct sun or when panels are hot to the touch.<\/li>\n<li><strong>Pre-rinse.<\/strong> Use a hose on low pressure or a pressure washer on a wide fan setting from a safe distance. Rinse top to bottom to remove loose grit before any contact.<\/li>\n<li><strong>Foam or pre-soak.<\/strong> Apply a diluted pH-neutral shampoo via foam gun or pump sprayer and let it dwell briefly. This lifts surface contamination before you touch the paint.<\/li>\n<li><strong>Two or three-bucket wash.<\/strong> Fill one bucket with shampoo solution and one (or two) with clean rinse water. Dip your mitt in the shampoo bucket, wash one panel at a time using straight lines (not circles), then rinse the mitt in the clean bucket before reloading. <a href=\"https:\/\/viridiandetailing.com.au\/blogs\/learn\/how-to-maintain-your-car-after-ceramic-coating\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">This method, combined with soft microfibre mitts, is the field-tested standard for protecting ceramic coatings<\/a>.<\/li>\n<li><strong>Wheels last.<\/strong> Use a dedicated bucket, brush, and mitt for wheels. Brake dust and road grime are abrasive; cross-contaminating your paint mitt is a common mistake.<\/li>\n<li><strong>Final rinse.<\/strong> Rinse the whole car top to bottom with low pressure. A sheeting rinse (hose without a nozzle) helps water run off quickly.<\/li>\n<li><strong>Dry immediately.<\/strong> Don\u2019t let the car air-dry. Use a clean, plush microfibre drying towel and pat or blot the surface rather than dragging the towel across it. Work panel by panel. A second dry towel for finishing removes any remaining moisture.<\/li>\n<\/ol>\n<p><strong>Pro Tip:<\/strong> <em>Rinse water quality matters more than most people realise. Hard tap water leaves mineral deposits that can etch a fresh coating. If your local water is hard, use a filtered hose attachment or dry the car quickly before water spots form.<\/em><\/p>\n<hr>\n<h2 id=\"products-and-tools-that-are-safe-for-the-first-wash\">Products and tools that are safe for the first wash<\/h2>\n<p>You don\u2019t need an expensive kit, but the wrong products can strip or weaken a new coating. Stick to these categories:<\/p>\n<ul>\n<li><strong>pH-neutral car shampoo.<\/strong> This is non-negotiable. Choosing a pH-neutral shampoo protects the coating\u2019s chemistry and avoids the alkaline or acidic damage that standard household detergents cause. Look for products labelled \u201ccoating safe\u201d or \u201cpH balanced.\u201d<\/li>\n<li><strong>Microfibre wash mitts.<\/strong> High-pile, soft mitts trap grit away from the paint surface. Avoid sponges, which hold grit against the panel.<\/li>\n<li><strong>Grit guards.<\/strong> Fit one in each bucket. They trap dirt at the bottom so your mitt doesn\u2019t pick it back up.<\/li>\n<li><strong>Microfibre drying towels.<\/strong> Use a plush, waffle-weave, or twisted-loop towel rated for paint-safe use. At least two per wash.<\/li>\n<li><strong>SiO2 maintenance spray.<\/strong> A monthly SiO2 spray applied during or after the wash refreshes hydrophobic performance and is commonly recommended by Australian detailers. Apply to a damp panel and buff off with a clean microfibre.<\/li>\n<li><strong>Iron fallout remover (pH-neutral).<\/strong> For decontamination washes every few months, not the first wash.<\/li>\n<\/ul>\n<p>Most of these products are available at local auto parts retailers across the Sunshine Coast and broader Australia, including Repco and Supercheap Auto. Pro-grade versions from specialist detailing suppliers offer better lubricity and coating compatibility, and typically cost more than entry-level supermarket alternatives.<\/p>\n<p><strong>Pro Tip:<\/strong> <em>Keep a small bottle of SiO2 maintenance spray and a folded microfibre in your boot. A quick spray on a clean, damp panel after a rinse takes two minutes and keeps the hydrophobic effect sharp between full washes.<\/em><\/p>\n<hr>\n<h2 id=\"common-mistakes-that-damage-a-newly-cured-coating\">Common mistakes that damage a newly cured coating<\/h2>\n<p>Most coating failures in the first month aren\u2019t product failures. They\u2019re aftercare failures. These are the mistakes worth knowing before you start.<\/p>\n<ul>\n<li><strong>Automatic or brush car washes.<\/strong> The brushes and harsh chemicals used in tunnel washes are among the fastest ways to degrade a coating. <a href=\"https:\/\/www.detailia.com.au\/learners-guide\/the-dos-and-donts-of-ceramic-aftercare\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Australian aftercare advice consistently warns against them<\/a>, and most installer warranties are voided by their use.<\/li>\n<li><strong>Acidic or alkaline cleaners.<\/strong> Wheel cleaners, bug removers, and all-purpose cleaners are often highly alkaline. Even a single use on a fresh coating can weaken its bond.<\/li>\n<li><strong>Single-bucket washing.<\/strong> Washing with one bucket reintroduces grit to the paint surface with every pass. Swirl marks from this are permanent without a machine polish.<\/li>\n<li><strong>Abrasive cloths or dirty mitts.<\/strong> A mitt that\u2019s been used on wheels, or a cloth that\u2019s been sitting on a garage floor, carries grit. One pass is enough to scratch.<\/li>\n<li><strong>Polishing over a fresh coating.<\/strong> Polish contains abrasives that will cut into or remove the coating layer. Never polish a coated car unless you intend to reapply.<\/li>\n<\/ul>\n<p>Watch for these warning signs during and after the first wash:<\/p>\n<ul>\n<li>Water spots that don\u2019t shift after drying (mineral deposits or etching)<\/li>\n<li>Hazing or streaking in direct light (possible contamination during cure)<\/li>\n<li>Patchy water beading (uneven cure or coating damage)<\/li>\n<\/ul>\n<p>If you see any of these, don\u2019t try to fix them yourself with a random product. Contact your installer first.<\/p>\n<blockquote>\n<p><strong>Warranty risk is real.<\/strong> Most professional ceramic coating warranties require you to follow the installer\u2019s aftercare instructions precisely. Using the wrong products, washing too early, or visiting an automatic car wash can void your warranty entirely. Keep a written record of your installer\u2019s instructions, the date of application, and every wash you perform. That documentation matters if you ever need to make a warranty claim. See <a href=\"https:\/\/isaacprodetailing.com.au\/index.php\/coating-warranty\" target=\"_blank\" rel=\"noopener\">Isaac\u2019s Pro Detailing\u2019s coating warranty terms<\/a> for an example of what installers typically require.<\/p>\n<\/blockquote>\n<hr>\n<h2 id=\"ongoing-care-after-the-first-wash-your-maintenance-schedule\">Ongoing care after the first wash: your maintenance schedule<\/h2>\n<p>A ceramic coating doesn\u2019t maintain itself. Regular washing remains necessary, with a recommended cadence ranging from weekly spot rinses to a full hand wash every 2\u20133 weeks and professional decontamination every 3\u201312 months depending on how much exposure the car gets.<\/p>\n<table>\n<thead>\n<tr>\n<th>Task<\/th>\n<th>Frequency<\/th>\n<th>Notes<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Light rinse or spot clean<\/td>\n<td>Every 7\u201310 days<\/td>\n<td>Remove bird droppings, sap, and road grime quickly<\/td>\n<\/tr>\n<tr>\n<td>Full pH-neutral hand wash<\/td>\n<td>Every 2\u20133 weeks<\/td>\n<td>Two-bucket method; dry immediately<\/td>\n<\/tr>\n<tr>\n<td>SiO2 maintenance spray<\/td>\n<td>Monthly<\/td>\n<td>Apply to damp panel; buff off with microfibre<\/td>\n<\/tr>\n<tr>\n<td>Iron fallout removal<\/td>\n<td>Every 3\u20136 months<\/td>\n<td>Use a pH-neutral iron remover; rinse thoroughly<\/td>\n<\/tr>\n<tr>\n<td>Professional decontamination<\/td>\n<td>Every 6\u201312 months<\/td>\n<td>Clay bar, iron removal, coating inspection<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><img decoding=\"async\" src=\"https:\/\/csuxjmfbwmkxiegfpljm.supabase.co\/storage\/v1\/object\/public\/blog-images\/organization-15772\/1786075343058_Maintenance-schedule-for-ceramic-coating-care.jpeg\" alt=\"Maintenance schedule for ceramic coating care\"><\/p>\n<p>Decontamination means removing bonded contamination that regular washing can\u2019t shift. Iron fallout from brake dust embeds in the coating surface over time; a pH-neutral iron remover dissolves it safely. Clay bar treatment removes other bonded particles. Both are best done by a professional on a coated car, particularly in the first year.<\/p>\n<p>Ceramic Pro Australia recommends hand washing with pH-neutral products and avoiding automatic car washes, and advises washing frequently enough to prevent contamination from building up. On the Sunshine Coast, where salt air, UV, and tree sap are constant factors, erring toward the shorter end of the wash cadence makes sense.<\/p>\n<hr>\n<h2 id=\"when-to-book-a-professional-first-wash-or-maintenance-service\">When to book a professional first wash or maintenance service<\/h2>\n<p>Some situations make a professional wash the smarter call, not just the easier one.<\/p>\n<ul>\n<li>Your installer recommends a professional maintenance wash as a warranty condition<\/li>\n<li>The car has heavy contamination from bird droppings, tar, or iron fallout<\/li>\n<li>You don\u2019t have the right tools (grit guards, quality mitts, pH-neutral shampoo)<\/li>\n<li>You\u2019re unsure whether a product you own is coating-safe<\/li>\n<li>You want a safe bird droppings removal done without risk to the coating<\/li>\n<\/ul>\n<p>A professional first wash or maintenance service typically includes a pre-rinse inspection, a safe two-bucket hand wash, light decontamination if needed, and a SiO2 maintenance spray to refresh the hydrophobic layer. You leave with a clean car, a documented service record, and no risk of having voided your warranty through an honest mistake.<\/p>\n<p><strong>Pro Tip:<\/strong> <em>Mobile detailing is particularly well-suited to the first wash window. The detailer comes to you, uses their own water supply and products, and works in a controlled environment. That removes the two biggest risks: wrong products and washing in direct sun on a hot driveway. Check the <a href=\"https:\/\/isaacprodetailing.com.au\/index.php\/wash-menu\" target=\"_blank\" rel=\"noopener\">Isaac\u2019s Pro Detailing wash menu<\/a> for available options on the Sunshine Coast.<\/em><\/p>\n<hr>\n<h2 id=\"a-sunshine-coast-detailers-practical-note\">A Sunshine Coast detailer\u2019s practical note<\/h2>\n<p>The Sunshine Coast\u2019s combination of intense UV, salt air, and eucalyptus trees creates conditions that test a fresh coating harder than most parts of Australia. The salt air alone accelerates water spotting on a partially cured surface, and gum sap can etch paint within hours if left untreated.<\/p>\n<p>The single habit that makes the biggest difference for local car owners is keeping a small SiO2 maintenance spray and two clean microfibres in the boot. After a beach run or a park under a gum tree, a quick spray and wipe takes less than five minutes and keeps the coating performing the way it should between full washes. It\u2019s not glamorous advice, but it\u2019s the thing that separates coatings that still look sharp at the three-year mark from ones that look average at twelve months.<\/p>\n<hr>\n<h2 id=\"isaacs-pro-detailing-mobile-first-wash-and-maintenance-on-the-sunshine-coast\">Isaac\u2019s Pro Detailing: mobile first wash and maintenance on the Sunshine Coast<\/h2>\n<p>Protecting a fresh ceramic coating starts with getting the first wash right, and that\u2019s exactly where a professional mobile service pays for itself. Isaac\u2019s Pro Detailing comes to your home, workplace, or wherever the car is parked across the Sunshine Coast, using warranty-safe, pH-neutral products and the correct two-bucket method every time.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/csuxjmfbwmkxiegfpljm.supabase.co\/storage\/v1\/object\/public\/blog-images\/organization-15772\/1770551132625_isaacprodetailing.jpg\" alt=\"Com\"><\/p>\n<p>Services include mobile maintenance washes, SiO2 top-ups, iron fallout removal, and full decontamination washes, all performed with eco-friendly products that won\u2019t compromise your coating or your warranty. No tunnel wash risk, no wrong products, no guesswork. Book a mobile maintenance wash through the wash menu and have your coating looked after by someone who knows exactly what it needs.<\/p>\n<hr>\n<h2 id=\"sources\">Sources<\/h2>\n<ul>\n<li><a href=\"https:\/\/ceramicpro.com\/wp-content\/uploads\/2022\/11\/Coating-Warranty-Aftercare.pdf\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Aftercare Instructions<\/a><\/li>\n<li><a href=\"https:\/\/kmautodetailing.com.au\/resources\/ceramic-coating-aftercare\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Ceramic Coating Aftercare: What to Do in the First 30 Days | KM Auto<\/a><\/li>\n<li><a href=\"https:\/\/viridiandetailing.com.au\/blogs\/learn\/how-to-maintain-your-car-after-ceramic-coating\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">How to Maintain a Ceramic Coating | Aftercare &amp; Maintenance<\/a><\/li>\n<li><a href=\"https:\/\/www.detailia.com.au\/learners-guide\/the-dos-and-donts-of-ceramic-aftercare\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">The Do\u2019s And Dont\u2019s Of Ceramic Aftercare. \u2014 Detailia<\/a><\/li>\n<li><a href=\"https:\/\/kovalentcoatings.com\/ceramic-coating-cure-time\/\" rel=\"nofollow noopener noreferrer\" target=\"_blank\">Ceramic Coating Cure Time Explained: A Complete Guide<\/a><\/li>\n<\/ul>\n<h2 id=\"recommended\">Recommended<\/h2>\n<ul>\n<li><a href=\"https:\/\/isaacprodetailing.com.au\/index.php\/2026\/06\/04\/types-of-protective-car-coatings-2026-guide\" target=\"_blank\" rel=\"noopener\">Types Of Protective Car Coatings: 2026 Guide<\/a><\/li>\n<li><a href=\"https:\/\/isaacprodetailing.com.au\/index.php\/2026\/06\/10\/what-is-advanced-car-protection-the-complete-guide\" target=\"_blank\" rel=\"noopener\">What Is Advanced Car Protection: The Complete Guide<\/a><\/li>\n<li><a href=\"https:\/\/isaacprodetailing.com.au\/index.php\/2026\/04\/11\/how-to-apply-ceramic-coating-step-by-step-guide\" target=\"_blank\" rel=\"noopener\">How To Apply Ceramic Coating: Step-by-step Guide For Car Owners<\/a><\/li>\n<li><a href=\"https:\/\/isaacprodetailing.com.au\/index.php\/2026\/06\/03\/step-by-step-ceramic-coating-application-guide\" target=\"_blank\" rel=\"noopener\">Step By Step Ceramic Coating Application Guide<\/a><\/li>\n<\/ul>\n","protected":false},"excerpt":{"rendered":"<p>Learn safe steps for your first wash after ceramic coating, ensuring long-lasting protection for your vehicle&#8217;s finish.<\/p>\n","protected":false},"author":1,"featured_media":3108,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_angie_page":false,"om_disable_all_campaigns":false,"_mi_skip_tracking":false,"order-bump-settings":[],"_wpfnl_thankyou_order_overview":"on","_wpfnl_thankyou_order_details":"on","_wpfnl_thankyou_billing_details":"on","_wpfnl_thankyou_shipping_details":"on","site-sidebar-layout":"default","site-content-layout":"default","ast-global-header-display":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","page_builder":"","two_page_speed":[],"footnotes":""},"categories":[1],"tags":[],"class_list":["post-3106","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-uncategorized"],"contentshake_article_id":"","_links":{"self":[{"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/posts\/3106","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/comments?post=3106"}],"version-history":[{"count":1,"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/posts\/3106\/revisions"}],"predecessor-version":[{"id":3107,"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/posts\/3106\/revisions\/3107"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/media\/3108"}],"wp:attachment":[{"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/media?parent=3106"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/categories?post=3106"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/isaacprodetailing.com.au\/index.php\/wp-json\/wp\/v2\/tags?post=3106"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}